ATY_LIB/FwLib_STC8/demo/adc/adc_interrupt_2ch.c

// Copyright 2021 IOsetting <iosetting(at)outlook.com>
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

/**
 * STC8H3K64S2
 *   AGrnd   -> GND
 *   AVcc    -> VCC
 *   AVref   -> VCC 
 *   Vcc     -> VCC
 *   Gnd     -> GND
 *   ADC1    -> Test voltage
 * 
 * STC8H1K08
 *   AVref   -> VCC 
 *   Vcc     -> VCC
 *   Gnd     -> GND
 *   ADC1    -> Test voltage
*/
#include "fw_hal.h"

uint8_t pos;
uint16_t res[2];

INTERRUPT(ADC_Routine, EXTI_VectADC)
{
    ADC_ClearInterrupt();
    res[pos] = ADC_RESL;
    res[pos] |= (ADC_RES & 0x0F) << 8;
    // Restart ADC for continuous sampling
    pos = (pos+1) & 0x1;
    if (pos == 0)
    {
        /**
         * Uncomment these lines in high speed ADC
        GPIO_P1_SetMode(GPIO_Pin_1, GPIO_Mode_InOut_OD);
        GPIO_P1_SetMode(GPIO_Pin_1, GPIO_Mode_Input_HIP);
        */
        ADC_SetChannel(0x01);
    }
    else
    {
        /**
         * Uncomment these lines in high speed ADC
        GPIO_P1_SetMode(GPIO_Pin_2, GPIO_Mode_InOut_OD);
        GPIO_P1_SetMode(GPIO_Pin_2, GPIO_Mode_Input_HIP);
        */
        ADC_SetChannel(0x02);
    }
    ADC_Start();
}

void main(void)
{
    SYS_SetClock();
    // For debug print
    UART1_Config8bitUart(UART1_BaudSource_Timer2, HAL_State_ON, 115200);
    // Channel: ADC1
    ADC_SetChannel(0x01);
    // ADC Clock = SYSCLK / 2 / (1+15) = SYSCLK / 32
    ADC_SetClockPrescaler(0x0F);
    // Right alignment, high 2-bit in ADC_RES, low 8-bit in ADC_RESL
    ADC_SetResultAlignmentRight();
    // Enable interrupts
    EXTI_Global_SetIntState(HAL_State_ON);
    EXTI_ADC_SetIntState(HAL_State_ON);
    // Turn on ADC power
    ADC_SetPowerState(HAL_State_ON);
    // Set ADC1(P1.1), ADC2(P1.2) HIP
    GPIO_P1_SetMode(GPIO_Pin_1|GPIO_Pin_2, GPIO_Mode_Input_HIP);
    // Start ADC
    ADC_Start();

    while(1)
    {
        UART1_TxString("Result: ");
        UART1_TxHex(res[0] >> 8);
        UART1_TxHex(res[0] & 0xFF);
        UART1_TxChar(' ');
        UART1_TxHex(res[1] >> 8);
        UART1_TxHex(res[1] & 0xFF);
        UART1_TxString("\r\n");
        SYS_Delay(100);
    }
}